Operation and setting
Power on/off Power on:
Press any key to wake up the screen, short press the power on button to enter the running time adjustment interface, adjust the running time according to different needs, press the left button to reduce the running time, press the right button to increase the running time, the running time can be set in the range 10-120min.When it is adjusted to 120min, press the right button again to set it to run for unlimited ∞ time. Please use this function with caution, it will consume a large amount of battery power and it will be difficult for the vehicle to start. After being turned on, after 60 seconds, the screen enters sleep mode, and a breathing light flashes in the center of the screen, indicating that the heater is on.
Press and hold the power on button for 5 seconds, the heater will directly enter the power-on interface according to the last running time.
Shutdown: Press any button to wake up the screen, press and hold the off button for 3 seconds, the heater will turn off, and the screen will return to the main menu interface. After 60 seconds, the screen enters sleep mode. Clock Ambient temperature Running time Ambient temperature Clock Power on/off/confirm button Right button/Up button Return button Left button/Down button Off state Power-on state Boot instructions.
Remote control matching
In the shutdown state, press the left button and the return button for 3 seconds to enter the remote control matching interface. At this time, press the ON or OFF button of the remote control once. After the match is successful, the interface will display OK. If the match is unsuccessful, it will display NOK. The words need to be re-matched with the .remote control. One timer can match two remotes at the same time.
Turn on/off the remote control
The remote control is a one-way remote control without return function, and the remote control distance is about 30 meters (in open areas). Power on the remote control: Short press the ON button of the remote control, the timer screen wakes up, and the screen displays the power-on interface at this time. After 60 seconds, it will enter the dormant state, and the breathing light will flash in the center of the screen. Turn off the remote control: Short press the OFF button of the remote control, the timer screen wakes up, and the screen returns to the main menu interface, and enters the sleep state after 60 seconds.
Time setting
Press any button to wake up the screen, select the setting with the left and right button, press the confirm button to enter the time setting (24 hours to), press the confirm button and the clock flashes, press the left and right button to adjust the clock, press the confirm button, the minutes flash, press the left and right button to adjust the minutes , And then press the confirm button to return to the clock screen. Press the left and right buttons to select the week setting, press the confirm button to enter the week setting interface, and press the left and right button to select the week（MON.TUE.WEN.THR.FRI.SAT.SUN.）.
Timer setting
Press any button to wake up the screen, select the P timing function with the left and right button, and press the confirm button to enter the timing interface. The three pre-selected times can be within the same day of the week or in different days. Press the confirm button to enter the P1 timing selection, then press the confirm button to select the day of the week, after pressing the confirm button, the clock flashes, adjust the clock, press the confirm button again to set the running time, and then press the confirm button, and use the left and right buttons to select ON or OFF , Finally press the confirm button, the screen returns to the main menu interface, at this time a dot prompt will appear in the upper left corner of the screen, and the timing function has been turned on. To set P2 and P3, please follow the above operations. When the pre-selected time is over, the √ behind P1 will be cancelled, indicating that P1 is over. If P2 and P3 do not turn on the timer function, the dot prompt in the upper left corner of the screen is turned off at this time. Clock setting Week setting Remote control matching
Function query
In the power-on state, press any key to wake up the screen, press the left and right button at the same time for 3 seconds to enter the function query interface, from top to bottom. Data arrangement: fan speed, voltage, oil pump frequency, water temperature, press the return button to return to the main menu interface.
