Thermal Management System Introduction
The thermal management system of electric vehicles has evolved from the thermal management system of traditional fuel vehicles, and the system configuration has also gradually developed from the relative independence of each thermal management circuit to the integration direction. Since there is no engine waste heat to be used, additional equipment is required to provide a heat source for heating the passenger compartment. Currently, the commonly used heating methods for electric vehicles include positive temperature coefficient (PTC) electric heater heating and heat pump air conditioning heating.
1. Single cooling air conditioner + PTC
The resistance of the thermistor in the PTC electric heater will increase with the increase of temperature, resulting in a decrease in heating power, so the PTC thermistor has a constant temperature characteristic. Due to the simple composition and low price of the PTC heating system, most early electric vehicles use single cooling air conditioner cooling and PTC electric heater heating to meet the cooling and heating needs of the passenger compartment. Figure 1 is a system diagram of single cooling air conditioner + PTC. In summer cooling, the evaporator arranged in the air duct is used to absorb heat to achieve the purpose of cooling. There are two solutions for heating. One is to arrange the air PTC directly in the air duct of the air conditioner box as shown in Figure 1 (a). When there is a heating demand, the PTC is energized to heat the air in the air duct and pass it into the passenger compartment; the other is to heat the refrigerant by the water PTC as shown in Figure 1 (b), and the refrigerant flows into the warm air core arranged in the air duct to indirectly heat the air in the air duct to meet the heating demand.

2. Heat pump air conditioning + PTC
Since PTC uses electric heating to heat, the heating efficiency is less than 1, so this heating method can reduce the driving range of electric vehicles by 50%. The theoretical efficiency of heat pumps is greater than 1, and using heat pumps instead of PTC heating has become a development trend. The research results of ZHANG et al. show that heat pump systems can save 41.3% of energy compared with PTC heater systems. Since most electric vehicles currently use R134a as the working fluid, when the ambient temperature is lower than −10 °C, the efficiency and reliability of the heat pump system are reduced, so PTC electric heaters are still required for auxiliary heating.
Figure 2 shows a heat pump air conditioning + PTC system using an electromagnetic four-way reversing valve and a three-heat exchanger. The heat pump air conditioning system switches between the cooling, heating, dehumidification, and defrosting modes of the system through the switch of the valve body. The four-way reversing valve has been widely used in the field of household air conditioning. Applying it to the electric vehicle heat pump air conditioning system can well solve the reversal problem of the refrigerant during system cooling and heating, as shown in Figure 2 (a). The system solution has few components, simple structure, and low cost. However, the copper-aluminum welding process of the four-way reversing valve is difficult and it is very easy to corrode. There is gas blowby on the high and low pressure sides, which affects the system performance. The heat pump air conditioning system of passenger cars usually adopts a three-heat exchanger solution with one outdoor heat exchanger and two indoor heat exchangers, and the mode is switched through multiple solenoid valves, as shown in Figure 2 (b).

3. Heat pump air conditioning + waste heat recovery + PTC
my country has a vast territory and a wide temperature range, so it is necessary to expand the temperature range of heat pump air conditioners. The waste heat of motors and batteries is a valuable heat source in winter. Many manufacturers and research institutions consider recycling this part of heat as an auxiliary heat source to expand the use of heat pump air conditioners.
Figure 3 is a diagram of an electric vehicle thermal management system using heat pump air conditioning + waste heat recovery + PTC. The system can realize functions such as passenger compartment cooling, heating, defrosting, defogging, and dehumidification. At the same time, it can heat or cool the battery and drive motor, and can also realize waste heat recovery of the battery and drive motor. The working principle of the system is as follows: the cooling, heating, dehumidification, defrosting and defoggering functions of the passenger compartment are realized through the switch combination of the refrigerant circuit solenoid valve; a battery cooler (Chiller) connected in parallel with the evaporator is added to the refrigerant circuit. When the battery or drive motor has a cooling demand, the refrigerant flows through the Chiller to cool the coolant in the secondary circuit; when the battery or drive motor does not have a large heat dissipation demand, the flow direction of the coolant can be controlled by switching the state of the three-way valve, and the heat can be discharged to the outside of the vehicle through the low-temperature radiator to achieve the cooling of the battery or drive motor; when the battery has a heating demand, the PTC is energized for heating and the heating function is achieved by adjusting the three-way valve on the coolant side; when the ambient temperature is low, the heat pump air conditioner cannot be used and the battery or drive motor has a heat dissipation demand, the coolant absorbs the heat that needs to be dissipated on the battery or drive motor side, flows through the Chiller through the three-way valve, and exchanges the heat to the refrigerant side to heat the passenger compartment, expanding the system's operating temperature range and improving the system's energy efficiency.






