Contact Us

    Hebei Nanfeng Automobile Equipment (Group) Co.,Ltd

    Phone: +86 18811334770

    Tel: +86 0317 8620396

    Tel: +86 010 58673556

    Candy Jiao

    E-mail: nh.jiao@auto-parkingheater.com

    Email: nh.li@auto-parkingheater.com

    Add: Room 505, Building B, Free Town Center, No.58, East Third Ring South Road, Chaoyang District, Beijing, 100022, P.R.China

Installation instructions of parking heaters

Sep 06, 2022

Installation instructions of water parking heaters in cars

liquid heater

parking heater.jpg
water  parking heater1.jpg


Connect the heater to the car cooling system according to Figures 3, 4 and 5. The cooling water present in the circulation loop must be at least 4 liters. The parking heater should be connected to the cooling water circulation loop in the inlet pipe of the car-bome heat exchanger. 

1.Installation of water pump

The water pump can be installed in the preset position on the heater, or it can be separated from the heater and installed in the water circulation loop. Be sure to pay attention to the correct direction of water flow (water outlet at the top / water inlet at the bottom). [ncorrect installation can cause malfunction of the pump.


2.Fuel line connection

water parking heater installation.jpg



Oil line in fuel tank without check valve 


You need to connect the oil circuit of the parking heater as shown in Figure 3 to the oil return pipe. Oil line system with check valve in oil tank and oil line system with single oil supply ; You need to install a connector of oil tank with 90°outlet on oil tank's fittmgs.(Figure 6)






3.Oil supply system

installation of water parking heater.jpg
water parking heater.jpg



Note: 

• The direction of oil flow can usually be identified from the mark on ttie oil filter. 

• If you want to take the oil from the oil supply pipe or the oil return pipe, you must use our fhctoiy's device of oil extraction, (Figure 8) 

• The installation of oil extraction device is able to allow any air or air bubbles can be automatically discharged to the oil tank. 

• The fuel should not be drawn out from nearby regions of tiie engine. Because the engine is radiating, air bubbles are likely to form in the tubing and cause operational faults.

• If the parking heater is installed in an electric spray car, you need to make sure whether the oil pump is installed inside or outside the oil tank. In addition, if the oil pump is installed inside ttie oil tank, you have to take the oil from the oil return pipe. For this purpose, you must ensure that the oil return pipe has a sufficient length to the bottom of the oil tank, otherwise the oil return pipe have to be extended.


4.Fuel line connection


water parking heater.jpg

Note: 

You need to tighten the hoop of oil pipeline with 1.0+0.4 Nm of tightening torque. 

Attention: 

• Because it cannot be confirmed that the oil pipeline is continuously laid upwards in most situations, the inner diameter of the oil pipeline must not exceed a established size. And if the oil pipeline is sagging or laying down slantingly, air bubbles will accumulate in oil pipeline with an inside diameter greater than 4 mm, then causing failure. All in all, if you use the diameter shown in Figure 7, it is guaranteed that no air bubbles will form The oil pipeline from the oil pump to the parking heater should not be laid obliquely downwards.

 • In order to avoid sagging, you should use the latest technical methods to fix the oil pipeline safely.

 • When installing the oil pipe, you should protect the pipe from hitting by gravel and high temperature (exhaust pipe).


5.Connecting two oil pipelines with a hose 

Figure 9 shows how to properly connect the fuel hose with a hose. Pay attention to the seal!

water parking heater (2)


6.Oil pump 

The oil pump is a combined system that combined by oil delivery, oil supply metering and fuel cut-off and it is bound to the relevant installation standards (see Figures 7,10, and 11). 


6.1 Installation location 

• Before you install the oil pump, make sure that the maximum pressure at the oil extraction point cannot exceed 0.2 bar. 

• It is recommended to install the pump in a low-temperature location. The ambient temperature cannot exceed +20°C during operation. 

• The oil pump and oil pipe must not be installed within the heat radiation range of hot car parts. You can use a heat shield if it is necessary. And the best installation location is near to the oil tank.

inatallation of parking heater


6.2 How to install and fix the oil pump 

You should use a shock-absorbing device to fix the oil pump. In order to ensure a good self-venting effect, the installation location should meet the requirements of Figures 10 and 11. 


7. The Label 

A label 'Turn off the heater when refueling" should be stuck to the filler port. In addition, you can also stick it in a position easily visible to the driver.


Send Inquiry