Three Control Modes Of Water Parking Heaters

Three control modes of water parking heaters

1、ON/OFF Controller

Wiring Schematic

Dimensions

Technical Parameter:

2、Digital Controller

The timer is used to turn on and off the heater equipment installed in the car, as well as to select the operating mode, set the operating time and pre-select the starting time. When entering the gas station, be sure to turn off the heater. 

The operation structure of the timer is simple. All functions can be set with 4 keys and can be changed when needed.If the car is powered off (the battery is disconnected) and then the power supply is restored, the time and day of the week must be reset.

Operation and setting：

2.1Power on/off 

Power on: Press any key to wake up the screen, short press the On key to enter the running time adjustment interface, adjust the running time according to different needs, press the Left key to reduce the running time, press the Right key to increase the running time, the running time can be set in the range 10-120min.When it is adjusted to 120min, press the Right key again to set it to run for unlimited ∞ time.Please use this function with caution, it will consume a large amount of battery power and it will be difficult for the vehicle to start. When the heater is turned on, after 60 seconds,the screen enters sleep mode, and a breathing light flashes in the center of the screen, indicating that the heater is on.

Press and hold the power On key for 5 seconds, the heater will directly enter the power-on interface according to the last running time. Shutdown: Press any button to wake up the screen, press and hold the Off key for 3 seconds, the heater will turn off, and the screen will return to the main menu interface. After 60 seconds, the screen enters sleep mode.

2.2Remote control matching

In the OFF state,press the left key and the Return key for 3 seconds to enter the remote control matching interface. At this moment, press the ON or OFF key of the remote control once. After the match is successful, the interface will display OK. If the match is unsuccessful, it will display NOK. This word means that the remotes need to be re-matched, a timer can match two remotes at the same time.

2.3Turn on/off the remote control 

The remote control is a one-way remote control without return function, and the remote control distance is about 30 meters (in open areas). 

• Turn on the remote control: Short press the ON key of the remote control ,the timer screen is woken up. At this time, the screen displays the power-on interface. After 60 seconds, it will enter the sleep state, and the breathing light will flash in the center of the screen.

• Turn off the remote control: Short press the OFF key of the remote control, the timer screen is woken up.At this time, the screen returns to the main menu interface . After 60 seconds,it will enter the sleep state. 

2.4Time Setting

Press any keys to wake up the screen, select the setting with the Left and Right key, press the Confirm key to enter the time setting (24 hours to), press the Confirm key and the clock flashes, press the Left and Right key to adjust the clock, press the Confirm key, the minute flashes, press the Left and Right key to adjust the minutes , And then press the Confirm key to return to the clock screen.

Press the  Left and Right key to select the week setting, press the Confirm key to enter the week setting interface, and press the Left and Right key to select the week（MON.TUE.WEN.THR.FRI.SAT.SUN.）. 

Clock Setting

Wee Setting

2.5 Timer Setting

Press any key to wake up the screen, select the P timing function with the Left and Right keys, and press the Confirm key to enter the timing interface. The three pre-selected times can be within the same day of the week or in different days.

Press the Confirm key to enter the P1 timing selection, then press the Confirm key to select the day of the week, after pressing the Confirm key, the clock flashes, adjust the clock, press the Confirm key again to set the running time, and then press the Confirm key, and use the Left and Right key to select ON or OFF , Finally press the Confirm key, the screen returns to the main menu interface, at this time a dot prompt will appear in the upper left corner of the screen, and the timing function has been turned on. To set P2 and P3, please follow the above operations.

When the pre-selected time is over, the √ behind P1 will be can celled, indicating that P1 is over. If P2 and P3 do not turn on the timer function, the dot prompt in the upper left corner of the screen is turned off at this time. 

2.6Function query 

In the On state, press any key to wake up the screen, press the Left and Right key at the same time for 3 seconds to enter the function query interface, from top to bottom. Data arrangement: fan speed, voltage,oil pump frequency, water temperature, press the Return key to return to the main menu interface. 

3、GSM Phone Control
3.1GSM module binding

The mobile phone module needs to be bound to control the mobile phone number of this device for the first time. This device can bind three mobile phone numbers, for example, the binding command, 1234ACCLIM: 1XXXXXXXXX: 1XXXXXXX:1XXXXXXXX: Three numbers, if it is a mobile phone number, the last two can be left blank. Note that the colon must be filled in. See "Attached Table" for SMS instructions.

3.2Manually bind numbers

If the GSM module has not been bound with a mobile phone number, you can press the manual switch once within 10 seconds of the light flashing when the GSM module is powered for the first time, and the indicator light is on. Then use the mobile phone with the mobile phone number that operates this module. , Make a call to the mobile phone number in the GSM module (you need to wait 10-60 seconds for the first connection) If the GSM module hangs up, the manual switch indicator goes out, which proves that the binding is successful.

3.3 GSM default working hours

The default working time of GSM and mobile phone modules is 30 minutes. In order to avoid the heater working time being longer than the driving time, causing the car battery to drain, we recommend that the heating time corresponds to the heater working time, (one way)

3.4GSM factory reset operation

Change the phone card,or re-bind the mobile phone number, you can restore the factory settings of the GSM module and re-bind it. The SMS command operation can restore the factory settings. Note that it must be a bound number to restore the factory settings. If the phone number cannot be operated, you can manually restore the factory settings. The steps are as follows: 1. Power off the GSM module, 2. Press and hold the manual switch of the GSM module without releasing it, 3. Power on the GSM module, and the manual switch will light up and release the manual switch. Power off the GSM for 5 seconds and restart the power supply. If the manual switch light flashes, it means that the factory settings are restored successfully.

3.5The phone activates the GSM module

After the number is successfully bound, you can start the GSM module with the call, dial the mobile phone number in the GSM module, wait for the GSM module to hang up, the GSM module rings 3 times to hang up, the GSM module starts, the manual switch indicator light is on, and Reply to the activated mobile phone number to activate the SMS command. If the signal is not good, there will be a delay in the response time, which is normal.