Contact Us
Hebei Nanfeng Automobile Equipment (Group) Co.,Ltd
Phone: +86 18811334770
Tel: +86 0317 8620396
Tel: +86 010 58673556
Candy Jiao
E-mail: nh.jiao@auto-parkingheater.com
Email: nh.li@auto-parkingheater.com
Add: Room 505, Building B, Free Town Center, No.58, East Third Ring South Road, Chaoyang District, Beijing, 100022, P.R.China
PTC Electric Coolant Heater
PTC Water Heater can provide heat for the cockpit of new energy vehicles and meet the standard of safe defrosting and defogging. At the same time, it provides heat to other parts of the vehicle that require temperature regulation.
Description
Product Highlights


This product is designed for a 430V voltage rating, a PTC chip thickness of 3.0mm, and a Tc temperature of 210℃, ensuring good voltage resistance and durability. The internal heating element assembly consists of 12 groups.
To ensure an IP67 protection rating, the heating element assembly is inserted at an angle into the lower base. The tube port sealing ring is installed, and the outer side is pressed tightly with a pressure plate. Then, the lower base is sealed with potting compound, which is then applied to the upper surface of the D-shaped tube. After assembling the other components, sealing gaskets are used to press and seal the upper and lower bases, ensuring good waterproof performance.
Products certification

Products Description
| Item | WPTC-13 |
| Rated voltage(VAC) | 430VAC (323-552VAC/50Hz&60Hz, three-phase four-wire power supply), inrush current I≤30A; |
| Ambient temperature | -40~105℃ |
| Ambient humidity | 5%~90%RH |
| Medium | 50% water/50% ethylene glycol |
| Heater protection grade | IP67 |
| Heater weight | 3.7±0.1Kg |
| Heater air tightness | apply pressure 0.6MPa, test for 3min, the leakage is less than 500Pa |

Products advantage

Design Advantages
① Employs a four-speed variable control method, resulting in low busbar inrush current and reduced requirements on relay electrical equipment in the vehicle's circuitry.
② Variable speed control allows for power adjustment at different speeds.
Control Functions
Outlet Water Temperature Over-Temperature Protection
When the outlet water temperature exceeds 85℃, all heating functions cease operation.
Related products
Products installation

To ensure optimal PTC efficiency, please note the following during installation
The highest point of the PTC should be lower than the expansion tank;
The water pump should not be higher than the PTC;
The PTC should be installed after the water pump and before the heater core;
Note the PTC's inlet and outlet water directions;
Before the PTC's first operation or after pipeline maintenance, start the water pump first and ensure it is emptied before connecting the PTC power supply.
Products Details





Products application



1. Cabin Heating (Water-based PTC / Air-based PTC)
Purpose: To heat the air conditioning coolant/air to provide warm air to the cabin, achieving cabin temperature control; in low-temperature environments where heat pump efficiency is insufficient, PTC acts as an auxiliary heat source to quickly raise the temperature, improving driving comfort.
2. Battery Preheating and Insulation (BTMS Battery Thermal Management)
Purpose: To raise the battery to its optimal operating temperature at low temperatures, improving charging speed and discharge power, reducing range degradation in winter, protecting cell life, and preventing the risk of lithium plating during low-temperature charging and discharging.
3. Window and Rearview Mirror Defrosting and Defogging
Purpose: To quickly melt frost and eliminate fog, ensuring safe driving visibility; the windshield mainly relies on warm air, while rearview mirrors mostly use thin-film heating elements for localized heating.
4. Onboard Sensor, Camera, and Radar Anti-freezing and De-icing
Purpose: To heat the housings of lidar and camera components to prevent frost and condensation, ensuring the normal operation of autonomous driving sensing equipment.
5. Seat and Steering Wheel Comfort Heating
Purpose: To provide localized body warmth and enhance the driving experience in winter.
Shipping

Products FAQ
Q: Does the electric water heater have a specific direction for its inlet and outlet? What happens if it's installed backwards?
A: There is a strict flow direction. The casing is generally marked IN for water inlet and OUT for water outlet. The medium comes from the radiator/battery circuit and enters through IN, flowing out through OUT to the battery pack/heater core.
Consequences of reverse installation: Disrupted internal flow, significantly reduced heat exchange efficiency, insufficient heating capacity, and a water temperature deviation fault report; in severe cases, localized overheating triggers over-temperature protection. It won't burn out directly, but the heating capacity will be greatly reduced.
Q: Are there any requirements for the heater's installation angle? Can it be installed upside down or at an angle?
A: Horizontal installation is preferred; a small angle of tilt is allowed; inverted installation with the outlet facing downwards is strictly prohibited.
The internal cavity must be filled with coolant. Inverting will cause localized air accumulation, leading to dry burning, triggering over-temperature protection, and eventually burning out the PTC core.
Q: After installation, how do I vent the cooling circuit? What fault will occur if I don't vent it?
A: According to the vehicle cooling system specifications, exhaust air from the low-pressure side to purge as much air as possible from the heater's interior.
Air in the cavity: Insufficient medium flow, localized high temperature inside the heater, triggering heater overheating and abnormal flow fault codes; inconsistent heating, insufficient power output.
Q: What precautions should be taken when assembling high-voltage and low-voltage connectors? Under what circumstances can they not be directly installed on the vehicle?
A: High-voltage connectors must be clicked into place; check for oxidation, water ingress, and pin retraction on the pins; ensure the sealing ring is intact and undamaged.
If the sealing ring is damaged, the housing is cracked, or the pins are corroded, installation is prohibited, as there is a risk of high-voltage leakage; low-voltage connectors should also be locked in place to avoid loose connections and communication fault reports.
Q: What are the high-voltage insulation requirements? How can I easily determine if the insulation is up to standard after installation?
A: National standards require that the insulation resistance between the high-voltage connector and the housing be ≥1000Ω/V; the insulation resistance of the 800V platform be ≥800kΩ.
The entire vehicle's insulation is tested; if the insulation is low, first check if water has entered the connector, if coolant has leaked into the high-voltage chamber, and if the heater housing is damp. High voltage is absolutely prohibited if the insulation is substandard.
Q: Is the low-voltage signal of the electric water heater CAN or hardwired? What signals are typically used?
A: The mainstream method is CAN bus communication (connected to BMS/VCU); a few low-cost solutions use hardwired enable + PWM power request.
Common signals: Heater operating status, actual output power, internal temperature, inlet water temperature, outlet water temperature, fault code, enable signal.
Hot Tags: PTC Electric Coolant Heater, China, factory, suppliers, manufacturers, seller, wholesale, quotation, high voltage automotive water heater, webasto heater, electric PTC heater for ev, new energy battery coolant heater for ev, high voltage heaters for electric vehicles, HEV coolant heater
You Might Also Like





















